Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Claremont
Gate repair in Claremont usually falls into two camps: a sagging original iron gate that needs custom hinge work, or an electric opener that quit without warning. Both are our specialty. Lexington Gate Repair sends technicians who know Claremont’s specific housing stock, from 1920s wrought-iron pedestrian gates near the Village to steel driveway gates on newer builds south of Foothill Boulevard. We’re based in Chino, so a truck can reach anywhere in the 91711 ZIP within about 30 to 45 minutes on a normal day. If your gate won’t open or won’t latch, call (866) 304-1321 and describe what you’re seeing. Nelson Arquette runs our service team, and he’ll make sure the right technician with the right parts heads your way.
Why Lexington Gate Repair Is Claremont’s Preferred Gate Repair Company
Claremont homeowners call us because we work on their specific brand of opener, not because we happen to carry a multimeter. LiftMaster, FAAC, BFT, Linear, Viking, and Ghost Controls all show up in Claremont driveways, and our technicians read error codes from each manufacturer rather than guessing. That matters when a FAAC hydraulic operator on a custom estate gate behaves differently than a Ghost Controls residential swing arm. We stock common Claremont parts in our Chino trucks: hinges, latch hardware, photocells, loop detector components, and opener control boards for the brands we service.
Being a gate specialist, not a generalist, is the whole point of Lexington Gate Repair. We don’t split our attention across fencing, garage doors, or patio covers. Every call is a gate call. Repairs, electric troubleshooting, realignment, hinge and post work, and full installations are what we do, and that focus means our techs see failure patterns that general contractors miss. Claremont’s older ironwork, especially hand-forged pieces from the 1920s, demands that kind of focused experience. Our Gate Repair team handles everything from stuck manual gates to full automation retrofits.
Claremont customers appreciate that the price gets quoted and agreed before any work starts. No wandering invoice after the job is done. That’s a promise we keep on every call, whether it’s a hinge replacement or a complete operator swap.
Styles & brands we work with
Commercial Gate Repair in Claremont
Commercial Gate Repair in Claremont covers the apartment complexes along Towne Avenue, HOAs near the Claremont Colleges, and business properties around the Village and Foothill Boulevard corridors. These systems run on DoorKing, FAAC, and BFT hardware more often than residential brands, and they see far more cycles per day than a private driveway gate ever will. A sliding gate at a Claremont apartment building might cycle 200 times daily, so worn rollers, tired motors, and misaligned safety photocells compound quickly. When an HOA gate fails, it isn’t an inconvenience anymore; it blocks emergency vehicles and daily traffic. That’s a different level of urgency. Commercial gate repair in Claremont typically runs $350 to $900 for most mechanical fixes, while control board replacement or full motor replacement can push into the $1,200 to $2,400 range depending on the operator model. We quote before we start, every time.
HOA and Apartment Access Systems
Claremont HOAs rely on access control that integrates with telephone entry systems and vehicle loop detectors. When a loop detector fails, the gate won’t hold open for exiting cars or won’t trigger for arriving ones. We diagnose the full loop circuit, not just the gate itself, because the problem often sits in the saw cut or the detector board rather than the operator. Property managers like that one call covers the entire access system.
Operator Replacement for Heavy Sliding Gates
Claremont’s commercial sliders run heavy. When a 600-pound gate wears out its operator, patching the old motor rarely makes sense. We spec the correct replacement for the gate’s weight and cycle rate, often replacing aged DoorKing or BFT units with modern operators that handle current UL 325 entrapment requirements. The install includes recalibrating force limits and verifying photocell alignment before we leave.
Iron Gate Repair in Claremont
Iron Gate Repair in Claremont is a different trade than it is in Upland or Rancho Cucamonga. That’s because Claremont’s historic core, especially the neighborhoods around the Claremont Colleges and west of Indian Hill Boulevard, is full of original 1920s wrought-iron gates with hand-forged hinges and latches. Off-the-shelf replacements don’t match. Worse, Claremont’s historic preservation review can require matching profiles for original ironwork, so a generic hinge from a hardware store fails inspection. We fabricate replacements that match the existing profile, preserving both function and the gate’s period appearance. Basic iron gate repair in Claremont starts around $180 to $320 for realignment, hinge tightening, or latch adjustment. Custom hinge fabrication runs $300 to $700, and full gate restoration with rust treatment and repainting typically lands between $900 and $2,000.
Hand-Forged Hinge and Latch Replacement
In the historic core near the Claremont Colleges, our tech replaced a hand-forged hinge on a 1920s wrought-iron pedestrian gate that had sagged for years; the hinge post footing had shifted, so we corrected the post and custom-fabricated a matching hinge profile to satisfy preservation review. The gate now swings silently and latches true, with a UV-resistant finish to handle the Santa Ana winds. That’s the kind of work a stock gate company walks away from, and it’s exactly what we’re built for.
Sag Repair and Gate Realignment
Iron gates sag because the hinge post moves or the hinges themselves wear oval. A sagging gate scrapes the ground, strains the latch, and stresses the operator if one is attached. We correct the post, replace or fabricate the hinges, and return the gate to plumb. On electric gates, realignment is part of the job because a misaligned operator fights the gate and burns out motors early.
Trusted Brands We Service in Claremont
We’re certified to service nine gate opener brands, including FAAC, BFT, Linear, and Viking. Those names matter in Claremont because the custom and semi-custom properties here often run FAAC hydraulic operators or BFT articulated arm systems, while older residential estates may have Linear or Viking units that have been in the ground for 15 years. Our Claremont customers get technicians who carry manufacturer-specific diagnostic knowledge and source correct parts, not universal substitutes. When a Viking control board dies, you want a tech who knows Viking error codes, not someone reading a generic forum post in your driveway. We stock common boards, photocells, remotes, and safety-edge parts in our service vehicles for faster turnaround.
Common Gate Repair Problems We See in Claremont Homes
- Hand-forged hinge wear on 1920s iron gates. The original hinges around the Colleges were made by hand, and after a century they wear unevenly. Off-the-shelf hinges won’t match the mounting pattern or the profile, so we fabricate replacements in-shop or on-site.
- Wooden gate warping from Santa Ana cycles. Claremont’s hot, dry summers and Santa Ana wind events pull moisture out of wooden driveway gates, then winter rains swell the wood back. The result is a gate that sticks in winter and rattles in summer. We adjust hinge post alignment seasonally and apply UV-resistant finishes that slow the cycle.
- Underground operator failures on large estates. Custom properties big enough for underground operators often hide their loop detectors and safety photocells near landscaping, and Claremont’s seasonal soil movement from moisture changes can misalign them. A gate that refuses to close is often a safety sensor out of position, not a dead motor.
- Latch misalignment after post settling. Many Claremont gates sit in stucco or masonry walls built decades ago. When the post shifts even a quarter inch, the latch won’t catch. We reset or reinforce the post rather than grinding the latch, because grinding buys six months and then you’re calling again.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Claremont, CA
A typical gate repair in Claremont costs between $180 and $700 for most mechanical fixes, with specific work landing in predictable ranges. Hinge realignment or latch adjustment runs $180 to $320. Electric gate diagnosis and minor electrical repair, like replacing a photocell or a limit switch, runs $200 to $400. Operator replacement on a standard residential swing gate runs $800 to $1,600 including labor, and custom iron hinge fabrication runs $300 to $700. Underground operator work on estates starts around $1,200 because of the excavation involved. You’ll get a firm price before any work begins, so there’s no invoice surprise. Call (866) 304-1321 and tell us what your gate is doing. The estimate is free, and we’ll tell you honestly whether it’s a repair or a replacement.
We Also Serve Cities Near Claremont
Lexington Gate Repair covers Claremont and the surrounding foothill communities, including Montclair, La Verne, Upland, and San Antonio Heights. If your gate is acting up and you’re just over the city line, we still take the call. The same technicians, the same brands, and the same upfront pricing apply across our full service area.
Serving Claremont, CA — Our Local Coverage Area
We’re based in the Claremont area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Claremont
Yes, and we do it regularly. Claremont’s historic preservation review requires matching profiles for original ironwork in designated historic neighborhoods, so we fabricate hinges and latches that replicate the existing hand-forged design rather than installing off-the-shelf hardware. We also document the work so you can show the review board. Call (866) 304-1321 for a repair assessment that respects the historic fabric of your gate.
Claremont’s cycle of hot, dry summers followed by winter rains causes wooden gates to swell and bind at the latch and hinge post. The fix is seasonal hinge realignment and, in many cases, replacing warped pickets or applying a UV-resistant finish that slows moisture absorption. We can assess whether your gate needs adjustment or a rebuild, and the price is quoted before work starts.
UL 325 requires that automatic gates have two independent entrapment protections, typically an inherent obstruction sensor in the operator plus an external device like photocells, contact edges, or a monitored safety loop. On a Claremont residential gate, that usually means a working reverse sensor and properly aligned photo eyes. If your gate reverses on nothing or won’t close with a car nearby, call us for a safety inspection; we can test your system and correct any deficiencies.
Usually the panel isn’t the problem. A sagging gate means the hinge post has moved or the hinges themselves have worn, and repairing only the panel ignores the root cause. We reset the post, replace or fabricate the hinges, and then align the panel. This is common on Claremont’s older iron gates where the original post footing has settled after decades of seasonal soil movement. Call (866) 304-1321 and we’ll tell you what’s actually moving.
Yes. Underground operators and integrated intercom or camera entry systems are common on larger Claremont properties, and we service both the operator and the access control wiring. We diagnose loop detectors, photocells, control boards, and the operator itself, and we stock parts for all nine brands we service. If your estate gate is misbehaving, call (866) 304-1321 for an estimate; we’ll have a tech out to diagnose it.
Call Lexington Gate Repair for Claremont Gate Service
Your gate is the first line of the property, whether it’s a 1920s iron pedestrian gate near the Village or a custom driveway slider on an estate. When it won’t close, won’t open, or won’t latch, call (866) 304-1321. We’ll send a gate specialist, not a generalist, and you’ll have a firm price before any work begins. From repair to replacement, we handle the whole job. Call today and tell us what your gate is doing.
Written by Nelson Arquette, Owner at Lexington Gate Repair, serving Claremont and the surrounding foothill communities.