Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Corona
Electric gate repair in Corona typically runs $180 – $520 depending on whether we’re replacing a sensor, rebuilding a motor, or realigning a wind-bent slide gate track. Most Corona jobs are finished same-visit because our trucks carry FAAC, BFT, Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Mighty Mule, and Elite parts as standard. If your gate won’t open on Green River Road or the opener grinds on a hillside off Foothill Parkway, call (866) 304-1321 and we’ll give you a straight diagnosis over the phone before we even dispatch.
We know Corona’s gate problems because we work them every week. Tract-home swing gates on the west flats fail differently than wrought-iron slide gates in Eagle Glen and Sierra Del Oro. That matters when you’re deciding whether a repair or a replacement is the smarter money.
Why Lexington Gate Repair Is Corona’s Preferred Electric Gate Repair Company
Lexington Gate Repair is a gate specialist, not a generalist. Nelson Arquette runs this company around one principle: a technician who only fixes gates will diagnose your problem correctly when a generalist won’t. Our Corona customers call us after handymen have already guessed wrong once, and the most common thing we hear is that we found the actual fault in under an hour.
We work on your brand. LiftMaster slide gates in Eagle Glen, FAAC swing arms on south Corona estates, BFT operators at HOA entrances, Linear boards in east-side subdivisions. When our van rolls into 92882, 92883, 92877, or 92878, our tech already knows the system type from your call and carries matching parts. That cuts return trips and keeps shared driveways clear.
Corona homeowners and property managers trust us because the diagnosis is right the first time. No upsell to a replacement when a gear or limit switch fixes it. No fencing-contractor markup on gate electronics that are outside their depth.
Styles & brands we work with
Electric Gate Motor in Corona
Electric gate motor repair in Corona means one of three things: the motor itself has failed, the capacitor that starts it has gone, or the operator board feeding it has a fault. In foothill neighborhoods off Weirick Road and in the 92883 corridor, we often find the motor is fine but the rack and pinion has jumped teeth after a Santa Ana wind event shifted the track. On the west flats, where the same opener has been running since the tract was built in the 1990s, the motor windings or the gearbox usually give out first. This job runs $220 – $480 in Corona depending on motor type and whether we’re rebuilding or replacing.
Motor Diagnostics on Wind-Exposed Slide Gates
Wind is the hidden variable here. A gate that binds against a bent track pulls more amps, and more amps cook the motor. So before replacing anything, we check track alignment, wheel drag, and limit travel. That sequence catches failures a board-swap might mask for six months.
Replacement Motors for Swing and Slide Systems
When the motor is truly dead, we quote the replacement up front, with the part number on the estimate. No surprise invoice. Your price is agreed before any work starts. Most replacement motors for Corona-area residential gates run $380 – $520 installed, including adjusting limits and testing the full safety circuit.
Gate Access Control in Corona
Gate access control in Corona covers everything that tells the gate who can come in: keypads, remote controls, loop detectors, safety photocells, and the control board that ties them together. This work runs $120 – $360 on average depending on the component. HOA and shared-driveway entrances around Home Gardens and El Cerrito Corona tend to need multiple remotes programmed and the loop detector sensitivity corrected, while single-family gates off Temescal Valley edges usually need a keypad rebuild or a new receiver.
Board Repair and Limit Switch Correction
When a gate opens partway and stops, the first thing we check is whether the board is retaining its limit settings. Control board repair in Corona starts at $180 – $240 for common Linear and FAAC boards. If the limit switch or encoder is the culprit, that’s often a $90 – $150 correction, not a board replacement. Checking the difference before buying parts is what brand-specific knowledge buys you.
Remote and Keypad Programming
We reprogram remotes and keypads on every brand we service, and a keypad replacement in Corona runs $120 – $200 depending on the model. If your keypad has a sun-cracked face and dead buttons after a few summers of direct west-side heat, we’ll say so and install one rated for hard UV exposure instead of giving you the same plastic that failed.
Trusted Brands We Service in Corona
Our Corona techs are certified on nine gate opener brands, and the three we see most here are FAAC and BFT on the estate gates and Linear on the older subdivision openers. Viking slide operators show up on commercial and some large ranch properties. We stock boards, gears, remotes, and sensors for all of them, so a Corona repair rarely waits on a parts truck from Chino. When the part is in the van, the repair is same-day.
Your gate, diagnosed correctly the first time. That’s the whole point of a brand-specific gate repair company.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Corona Homes
- Wind-bent slide gate tracks and skipped rack teeth. Fall Santa Ana winds push fences and gates in Eagle Glen and Sierra Del Oro hard enough to shift track alignment. When the rack and pinion jump a tooth, the gate grinds and shudders instead of gliding. We realign and replace the worn rack section, then reset operator limits so the motor isn’t fighting the wind.
- Sun-warped wood and cracked vinyl on west-side swing gates. Corona’s inland heat dries wood gates to the point where stiles bow and hinges loosen seasonally. Vinyl gates fade and crack within a few summers. Both problems stress the operator and cause the motor to trip its thermal overload.
- Shared driveways that force slide gate retrofits. Tight setbacks near downtown Corona and in 92882 leave no room for a swing gate arc. Slide gate retrofits work, but the loop detector and safety photocells have to be placed carefully so the gate doesn’t close on a neighbor’s car mid-turn. We handle the access problem as part of the repair, not an afterthought.
- Safety sensor faults from dust and heat cycling. Dry inland conditions and wide temperature swings make photocell housings expand and contract, and dust blows into the lens. A dirty or misaligned sensor reads as a gate that won’t close or reverses for no reason. This is a $95 – $160 fix in most of Corona and we’d rather do that than sell you a board you don’t need.
Pricing for Electric Gate Repair in Corona, CA
Here’s what electric gate repair actually costs in Corona. A gate that won’t open and turns out to be a safety sensor runs $95 – $160. A keypad replacement runs $120 – $200. A control board replacement runs $180 – $240 for common Linear and FAAC boards. An electric gate motor replacement runs $220 – $480 depending on swing vs. slide and motor wattage. Full slide gate track realignment after wind damage runs $280 – $520 including rack repair. These are real numbers for this market, not national averages. Call (866) 304-1321, describe the symptom, and we’ll give you an exact quote over the phone. Estimates are free, and the price is always agreed before work starts.
We Also Serve Cities Near Corona
Lexington Gate Repair runs calls from Home Gardens and El Cerrito Corona through Eastvale and Norco, and we treat all of them the same way: a gate specialist at your door with parts in the van. If your gate is down anywhere in the Corona area, call (866) 304-1321 and we’ll get the repair started today.
Serving Corona, CA — Our Local Coverage Area
We’re based in the Corona area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Corona
Yes. When we work on a shared driveway gate in Corona, we keep one side operational or schedule the work so the gate is fully functional during peak morning and evening hours. Slide gate work near a shared right of way usually means we remove panels in sections rather than blocking the whole opening. We also coordinate with the neighbor or HOA so everyone knows the timeline ahead of the repair. Call (866) 304-1321 and we’ll walk you through the plan.
In Sierra Del Oro and Eagle Glen, the usual culprit is a bent or shifted slide gate track that has allowed the rack and pinion gear to jump a tooth. Santa Ana winds push the gate sideways just enough to change the mesh, and from there every cycle grinds the gear. We realign the track, replace the damaged rack section, and reset the operator’s limit switches. It’s a $280 – $520 job in most cases and we’re on it the same week in most of Corona.
Test it with a solid object like a traffic cone or a piece of lumber, never your body. When the gate closes and hits the object, it should stop and reverse immediately. If it keeps pushing or slows but doesn’t reverse, the safety photocells or the internal force setting need adjustment. We check entrapment protection on every Corona repair, and a sensor repair or replacement is usually $95 – $160. If your gate doesn’t reverse, do not use it until it’s fixed. Call us and we’ll correct it the same visit.
Yes. We service LiftMaster and FAAC gate operators in Corona along with BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. FAAC swing and slide arms are common on the estate properties in 92883. LiftMaster slide gates dominate the Eagle Glen and Sierra Del Oro hillsides. Our techs carry board, gear, and sensor parts for both brands in the van, so most repairs happen in one visit.
In most west Corona cases the best fix is a hinge and post reset, not a whole gate rebuild. The hinge screws pull out of the dried stucco or wood post, the gate sags, and that throws the entire operator out of alignment. We pull the gate square, reset the hinges with structural hardware, and adjust the operator so it moves the gate without strain. It’s a $150 – $280 fix in most of the 92882 and 92877 areas versus $1,200 or more for a new gate you may not need. Call (866) 304-1321 for an honest diagnosis.
Written by Nelson Arquette, Owner at Lexington Gate Repair, serving Corona since 2006.